Documentation › Troubleshooting
Troubleshooting
The things that most often go wrong, and what to do about each.
Installing and signing in
“Windows protected your PC”
Windows shows this for an installer it has not seen often. Check that you downloaded it from this site, then choose More info and Run anyway.
The browser did not open, or sign-in did not finish
Choose Help › Account and licence and sign in again. A sign-in link sent by e-mail works once, for 20 minutes. If the page says the request has run out, go back to Gusset and start again from there.
It says I am signed out on a computer I use
A licence signs in on two computers. Signing in on a third signs out the one unused for longest. Sign in again on the one you want; your account page lists them.
Opening a model
Parts are missing
Bodies that are not closed solids are skipped, and Gusset lists what it left out. In CAD, check that each part is a solid and not a surface, and export again as STEP.
The model is a thousand times too big or too small
A mesh file has no units. Open it again and choose the right ones when asked. STEP files carry their units, so exporting STEP avoids the question.
My SolidWorks, Inventor or other CAD file will not open
Native CAD files are not read. Export STEP.
Setting up
Parts that should be joined are not
They have to touch. Faces further apart than the gap tolerance are not joined. Close the gap in CAD, or raise Weld gap tolerance under Solution settings. Look under Connections in the tree to see which pairs were found.
No bolts were found
- A new study bonds parts all over and looks for no bolts. Untick Bond touching parts all over under Welds, or set the pair to Bolted.
- The holes must line up on one axis through parts that touch.
- A hole much larger than a bolt, or one with a modelled shaft through it, is not taken for a bolt hole.
“These faces are not one cylindrical hole”, for a pin or an anchor bolt
Pick the curved faces inside the hole, not the flat face around it. A hole is often two half-cylinders: Ctrl-click to pick both.
The solve is refused because a part is free to move
Something is not held. The message names the movement. Join the part to its neighbours, or add a fixture that stops it. A part held only at centre points can still spin about the line between them.
Solving
It is slow, or runs short of memory
- Solve at Draft or Fast first to check the setup, then raise the accuracy.
- Keep Refine only where the solution still changes ticked.
- Use Bolts: quick unless you need contact pressure.
- Give the one part you care about a finer Accuracy and leave the study at Standard.
- If the joints are not what you are checking, export the model from CAD as one body.
- Close other programs. Each pass needs several times the memory of the one before.
“Not converged”, or passes were not run
Choose Solve one pass more. If the verdict says a pass did not fit in memory, the results shown are from the last pass that did: use the steps above to make the model smaller, or treat the stresses as low.
The verdict will not settle however many passes I add
Open Why?. If the stress that keeps moving is at a sharp inside corner or a weld root, it never will: see Peaks you should not believe. Model the real fillet, or judge the part by the stress away from the corner.
Results
The plot is all one colour
One small peak has stretched the scale. Type a lower value in the box at the top of the legend, such as the yield strength. See the legend.
The model deforms wildly
The deformation is multiplied so that you can see it. Set the Deformation group to True scale to see it as it is, and read the real size from the Displace plot.
The deflection is far larger than I expected
- Check the load: a force is the total over the faces, in newtons.
- Check the material, and the units of a mesh file.
- Play the animation. A part swinging freely about a pin or a centre point is held less than you meant.
The stress is far lower than I expected
Check the verdict: a coarse model reads low. Then check the reactions in the report against the loads you meant to apply.
A printed part carries a note about a guessed direction
Set Stacked along in the Material panel. See 3D prints.
Still stuck?
E-mail us with what you did and what happened. A screenshot helps, and so does the report if you can share it. Your model stays on your computer unless you choose to send it.
Something wrong or missing on this page? Tell us.